Survey Control Points and Benchmarks: Why They Matter on UAE Projects

Survey control points are fixed, measured reference marks that give every measurement on a project a common position, and benchmarks are reference marks with a known height. Together they make sure that the survey, the design and the construction all refer to the same positions and levels. Without them, work done by different teams or at different times may not line up. This guide explains what control points and benchmarks are, how they are used and cared for, and where Sail Survey Global, a land surveying company in Dubai, fits among surveying companies in Dubai.

What is a survey control point?

A control point is a marked position on or near a site whose coordinates have been measured with care. It might be a nail in a kerb, a mark on a concrete pad or a pin set in the ground. Surveyors set up their instruments on these points, or measure from them, so every new measurement is tied back to the same reference. Control is usually set up as a network of several points, so that they can be checked against each other.

What is a benchmark?

A benchmark is a stable, marked point with a known height. Levels on the site are measured from benchmarks, so that the height of a floor, a road or a drain is stated against the same reference. Benchmarks should sit on something that will not move, such as a solid structure, and away from traffic and construction work.

Why they matter

  • Consistency. Everyone measures from the same references, so results agree.
  • Repeatability. A survey can be repeated later and compared, because the references are still there.
  • Setting out. Design positions are marked on the ground from control points.
  • Checking. Control gives the means to check whether work was built where the design said.
  • Handover. As-built records tie back to the same reference as the original survey.

Coordinate system and datum

Control points have coordinates in a defined coordinate system, and benchmarks have heights from a defined level datum. These must be stated on the survey drawings and agreed by everyone who uses them. If the survey team, the designer and the contractor use different systems, the data may not match. This article does not name specific systems, because the right one depends on the project and the authority involved. Confirm it in the project documents before work starts.

How control is established

  1. Plan the network. Choose stable positions that can see each other and the site.
  2. Mark the points. Use durable marks that are easy to find again.
  3. Measure with care. Measure the network with suitable instruments and repeat measurements to check them.
  4. Tie to a reference. Connect the network to a recognised coordinate system and level reference.
  5. Record and share. Issue a list of coordinates, heights and point descriptions to the project team.

How to look after control points

  • Protect marks from machinery, paving, painting and excavation.
  • Keep a description or photograph of each point so that it can be found.
  • Re-check key points at intervals, and before important setting out.
  • Re-establish any point that is damaged or moved, and tell the team.
  • Do not use a point if it looks disturbed until it has been checked.

Common signs of a control problem

  • Two surveys of the same feature disagree by more than expected.
  • Setting-out marks do not match the design when checked from another point.
  • Levels from two benchmarks do not agree.
  • A mark has been covered, moved or damaged.

When any of these appear, stop and check the control before continuing. Building on a wrong reference creates errors that are expensive to fix later.

Where control fits in the project

StageRole of control
Site surveyTies the survey to a common reference
DesignAllows design drawings to sit on the survey correctly
Setting outSource of positions and levels marked on the ground
Construction checksReference for checking built work
As-built surveyTies final records to the same reference

Where does Sail Survey Global fit?

Sail Survey Global, registered as Sail Real Estate Survey Services, is a land surveying company based in Dubai. When you brief any provider, including Sail Survey Global, ask which control the survey will use, how it will be marked and protected, and which coordinate system and datum will be stated on the drawings.

Common mistakes to avoid

  • Not agreeing the coordinate system and datum at the start.
  • Placing control where construction will destroy it.
  • Using a point without checking that it has not moved.
  • Keeping control records only with one person.
  • Different teams setting up their own control with no tie between them.

Frequently asked questions

What are survey control points?

Marked reference positions with measured coordinates, used as the common base for all measurements on a site.

What is a benchmark in surveying?

A stable marked point with a known height, used as the reference for levels.

Why do control points get re-checked?

Marks can be moved or damaged, and a check confirms they can still be trusted.

Who should hold the control records?

The survey company and the project team, so the information is not lost if people change.

 

Comments

  • No comments yet.
  • Add a comment